File Name: difference between capstan and turret lathe ppt to .zip
A capstan and turret lathe is used to manufacture any number of identical workpieces in less time.
- Difference Between Capstan and Turret Lathes
- Capstan and Turret Lathe: Working, Advantages, Bar Feeding Mechanism (With PDF)
- Metal lathe
Difference Between Capstan and Turret Lathes
A metal lathe or metalworking lathe is a large class of lathes designed for precisely machining relatively hard materials. They were originally designed to machine metals ; however, with the advent of plastics and other materials, and with their inherent versatility, they are used in a wide range of applications, and a broad range of materials. In machining jargon , where the larger context is already understood, they are usually simply called lathes , or else referred to by more-specific subtype names toolroom lathe , turret lathe , etc.
These rigid machine tools remove material from a rotating workpiece via the typically linear movements of various cutting tools, such as tool bits and drill bits. The design of lathes can vary greatly depending on the intended application; however, basic features are common to most types. These machines consist of at the least a headstock, bed, carriage, and tailstock.
Better machines are solidly constructed with broad bearing surfaces slide-ways for stability, and manufactured with great precision. This helps ensure the components manufactured on the machines can meet the required tolerances and repeatability. The headstock is required to be made as robust as possible due to the cutting forces involved, which can distort a lightly built housing, and induce harmonic vibrations that will transfer through to the workpiece, reducing the quality of the finished workpiece.
The main spindle is generally hollow to allow long bars to extend through to the work area. This reduces preparation and waste of material. The spindle runs in precision bearings and is fitted with some means of attaching workholding devices such as chucks or faceplates. This end of the spindle usually also has an included taper , frequently a Morse taper , to allow the insertion of hollow tubular Morse standard tapers to reduce the size of the tapered hole, and permit use of centers.
On older machines '50s the spindle was directly driven by a flat belt pulley with lower speeds available by manipulating the bull gear. Later machines use a gear box driven by a dedicated electric motor. A fully 'geared head' allows the operator to select suitable speeds entirely through the gearbox. The bed is a robust base that connects to the headstock and permits the carriage and tailstock to be moved parallel with the axis of the spindle.
This is facilitated by hardened and ground bedways which restrain the carriage and tailstock in a set track.
The carriage travels by means of a rack and pinion system. The leadscrew of accurate pitch, drives the carriage holding the cutting tool via a gearbox driven from the headstock. Types of beds include inverted "V" beds, flat beds, and combination "V" and flat beds.
When a lathe is installed, the first step is to level it, which refers to making sure the bed is not twisted or bowed. There is no need to make the machine exactly horizontal, but it must be entirely untwisted to achieve accurate cutting geometry. A precision level is a useful tool for identifying and removing any twist. It is advisable also to use such a level along the bed to detect bending, in the case of a lathe with more than four mounting points.
In both instances the level is used as a comparator rather than an absolute reference. The feedscrew H8 is a long driveshaft that allows a series of gears to drive the carriage mechanisms. These gears are located in the apron of the carriage. Both the feedscrew and leadscrew H7 are driven by either the change gears on the quadrant or an intermediate gearbox known as a quick change gearbox H6 or Norton gearbox.
These intermediate gears allow the correct ratio and direction to be set for cutting threads or worm gears. Tumbler gears operated by H5 are provided between the spindle and gear train along with a quadrant plate that enables a gear train of the correct ratio and direction to be introduced.
This provides a constant relationship between the number of turns the spindle makes, to the number of turns the leadscrew makes. This ratio allows screwthreads to be cut on the workpiece without the aid of a die. Some lathes have only one leadscrew that serves all carriage-moving purposes. For screw cutting, a half nut is engaged to be driven by the leadscrew's thread; and for general power feed, a key engages with a keyway cut into the leadscrew to drive a pinion along a rack that is mounted along the lathe bed.
The leadscrew will be manufactured to either imperial or metric standards and will require a conversion ratio to be introduced to create thread forms from a different family. To accurately convert from one thread form to the other requires a tooth gear, or on lathes not large enough to mount one, an approximation may be used. Multiples of 3 and 7 giving a ratio of can be used to cut fairly loose threads. This conversion ratio is often built into the quick change gearboxes. This transposition gives a constant In its simplest form the carriage holds the tool bit and moves it longitudinally turning or perpendicularly facing under the control of the operator.
The operator moves the carriage manually via the handwheel 5a or automatically by engaging the feed shaft with the carriage feed mechanism 5c. This provides some relief for the operator as the movement of the carriage becomes power assisted. The handwheels 2a, 3b, 5a on the carriage and its related slides are usually calibrated, both for ease of use and to assist in making reproducible cuts. The carriage typically comprises a top casting, known as the saddle 4 , and a side casting, known as the apron 5.
The cross-slide 3 rides on the carriage and has a feedscrew which travels at right angles to the main spindle axis. This permits facing operations to be performed, and the depth of cut to be adjusted.
This feedscrew can be engaged, through a gear train, to the feed shaft mentioned previously to provide automated 'power feed' movement to the cross-slide. On most lathes, only one direction can be engaged at a time as an interlock mechanism will shut out the second gear train.
Cross-slide handwheels are usually marked in terms of the part's diameter , so one graduation representing. The compound rest or top slide 2 is usually where the tool post is mounted.
It provides a smaller amount of movement less than the cross-slide along its axis via another feedscrew. The compound rest axis can be adjusted independently of the carriage or cross-slide. It is used for turning tapers, to control depth of cut when screwcutting or precision facing, or to obtain finer feeds under manual control than the feed shaft permits. Usually, the compound rest has a protractor marked in its base 2b , enabling the operator to adjust its axis to precise angles.
The slide rest as the earliest forms of carriage were known can be traced to the fifteenth century. In the tool-supporting slide rest with a set of gears was introduced by a Russian inventor Andrey Nartov and had limited usage in the Russian industry. The first fully documented, all-metal slide rest lathe was invented by Jacques de Vaucanson around It is likely that Maudslay was not aware of Vaucanson's work, since his first versions of the slide rest had many errors that were not present in the Vaucanson lathe.
In the eighteenth century the slide rest was also used on French ornamental turning lathes. The suite of gun boring mills at the Royal Arsenal , Woolwich , in the s by the Verbruggan family also had slide rests.
The story has long circulated that Henry Maudslay invented it, but he did not and never claimed so. The legend that Maudslay invented the slide rest originated with James Nasmyth , who wrote ambiguously about it in his Remarks on the Introduction of the Slide Principle , ;  later writers misunderstood, and propagated the error. However, Maudslay did help to disseminate the idea widely. It is highly probable that he saw it when he was working at the Arsenal as a boy.
In , whilst he was working for Joseph Bramah , he made one, and when he had his own workshop used it extensively in the lathes he made and sold there. Coupled with the network of engineers he trained, this ensured the slide rest became widely known and copied by other lathe makers, and so diffused throughout British engineering workshops. A practical and versatile screw-cutting lathe incorporating the trio of leadscrew, change gears, and slide rest was Maudslay's most important achievement.
The tool bit is mounted in the toolpost 1 which may be of the American lantern style, traditional four-sided square style, or a quick-change style such as the multifix arrangement pictured. The advantage of a quick change set-up is to allow an unlimited number of tools to be used up to the number of holders available rather than being limited to one tool with the lantern style, or to four tools with the four-sided type. Interchangeable tool holders allow all tools to be preset to a center height that does not change, even if the holder is removed from the machine.
The tailstock is a tool drill , and center mount, opposite the headstock. The spindle T5 does not rotate but does travel longitudinally under the action of a leadscrew and handwheel T1. The spindle includes a taper to hold drill bits, centers and other tooling. The tailstock can be positioned along the bed and clamped T6 in position as dictated by the work piece. There is also provision to offset the tailstock T4 from the spindles axis, this is useful for turning small tapers, and when re-aligning the tailstock to the axis of the bed.
The image shows a reduction gear box T2 between the handwheel and spindle, where large drills may necessitate the extra leverage. The tool bit is normally made of HSS, cobalt steel or carbide. Long workpieces often need to be supported in the middle, as cutting tools can push bend the work piece away from where the centers can support them, because cutting metal produces tremendous forces that tend to vibrate or even bend the workpiece.
This extra support can be provided by a steady rest also called a steady , a fixed steady , a center rest , or sometimes, confusingly, a center. A follower rest also called a follower or a travelling steady is similar, but it is mounted to the carriage rather than the bed, which means that as the tool bit moves, the follower rest "follows along" because they are both rigidly connected to the same moving carriage. Follower rests can provide support that directly counteracts the springing force of the tool bit, right at the region of the workpiece being cut at any moment.
In this respect they are analogous to a box tool. Any rest transfers some workpiece geometry errors from base bearing surface to processing surface. It depends on the rest design. For minimum transfer rate correcting rests are used. Rest rollers typically cause some additional geometry errors on the processing surface. There are many variants of lathes within the metalworking field. Some variations are not all that obvious, and others are more a niche area.
For example, a centering lathe is a dual head machine where the work remains fixed and the heads move towards the workpiece and machine a center drill hole into each end. The resulting workpiece may then be used "between centers" in another operation. The usage of the term metal lathe may also be considered somewhat outdated these days. Plastics and other composite materials are in wide use and, with appropriate modifications, the same principles and techniques may be applied to their machining as that used for metal.
The terms center lathe , engine lathe , and bench lathe all refer to a basic type of lathe that may be considered the archetypical class of metalworking lathe most often used by the general machinist or machining hobbyist. The name bench lathe implies a version of this class small enough to be mounted on a workbench but still full-featured, and larger than mini-lathes or micro-lathes. The construction of a center lathe is detailed above, but depending on the year of manufacture, size, price range or desired features, even these lathes can vary widely between models.
Engine lathe is the name applied to a traditional lateth-century or 20th-century lathe with automatic feed to the cutting tool, as opposed to early lathes which were used with hand-held tools, or lathes with manual feed only.
The usage of "engine" here is in the mechanical-device sense, not the prime-mover sense, as in the steam engines which were the standard industrial power source for many years. The works would have one large steam engine which would provide power to all the machines via a line shaft system of belts.
Capstan and Turret Lathe: Working, Advantages, Bar Feeding Mechanism (With PDF)
What Is Lathe? A lathe is a machine tool which rotates the workpiece on its axis to perform various operations such as cutting, sanding, knurling, drilling, or deformation with tools that are applied to the workpiece to create an object which has symmetry about an axis of rotation. Development of Lathes: Turret and capstan lathes are the natural development of the engine lathe, where the tailstock is replaced by an indexable multistation tool head, called the capstan or the turret. This head carries a selection of standard tool holders and special attachments. A square turret is mounted on the cross slide in place of the usual compound rest in engine lathe.
A metal lathe or metalworking lathe is a large class of lathes designed for precisely machining relatively hard materials. They were originally designed to machine metals ; however, with the advent of plastics and other materials, and with their inherent versatility, they are used in a wide range of applications, and a broad range of materials. In machining jargon , where the larger context is already understood, they are usually simply called lathes , or else referred to by more-specific subtype names toolroom lathe , turret lathe , etc. These rigid machine tools remove material from a rotating workpiece via the typically linear movements of various cutting tools, such as tool bits and drill bits. The design of lathes can vary greatly depending on the intended application; however, basic features are common to most types. These machines consist of at the least a headstock, bed, carriage, and tailstock. Better machines are solidly constructed with broad bearing surfaces slide-ways for stability, and manufactured with great precision.
The main difference between the capstan and turret lathe machine is the capstan lathe is fast because of light construction but the turret lathe is slow (rigid.
A capstan and turret lathe is a production lathe. It is used to manufacture any number of identical pieces in the minimum time. In semi-automatic lathes machining operations are done automatically. Functions other than machining like loading and unloading of a job, the positioning of tools coolant operations are done manually. Turret head has a hexagonal block having six faces with a bore for mounting six or more than six tools at a time.
The turret lathe is a form of metalworking lathe that is used for repetitive production of duplicate parts, which by the nature of their cutting process are usually interchangeable. It evolved from earlier lathes with the addition of the turret , which is an indexable toolholder that allows multiple cutting operations to be performed, each with a different cutting tool , in easy, rapid succession, with no need for the operator to perform set-up tasks in between such as installing or uninstalling tools or to control the toolpath. The latter is due to the toolpath's being controlled by the machine, either in jig -like fashion, via the mechanical limits placed on it by the turret's slide and stops, or via electronically -directed servomechanisms for computer numerical control lathes. The name derives from the way early turrets took the general form of a flattened cylindrical block mounted to the lathe's cross-slide, capable of rotating about the vertical axis and with toolholders projecting out to all sides, and thus vaguely resembled a swiveling gun turret. There are many variants of the turret lathe.
No Capstan lathe 1 It is a light duty machine The turret head is mounted on the ram and 2 the ram is mounted on the saddle.
Capstan and Turret Lathe is one of the types of Lathe Machine. These machines used for mass production. The main difference between the capstan and turret lathe machine is the capstan lathe is fast because of light construction but the turret lathe is slow rigid construction.
Если бы я сумел слегка модифицировать этот код, - продолжал Стратмор, - до его выхода в свет… - Он посмотрел на нее с хитрой улыбкой. Сьюзан потребовалось всего мгновение. Стратмор сразу заметил изумление, мелькнувшее в ее глазах, и взволнованно изложил свой план: - Если бы я получил ключ, то смог бы взломать наш экземпляр Цифровой крепости и внести нужные изменения… - Черный ход, - сказала Сьюзан, мгновенно забыв о том, что Стратмор ей лгал.
Беккер на своем мотоцикле скрылся в узком проходе Каллита-де-ля-Вирген. ГЛАВА 88 Фара веспы отбрасывала контрастные тени на стены по обе стороны от узкой дорожки.